共找到 150 條與 掃描電子顯微鏡法 相關的標準，共 10 頁
5.1 This test method is established to cover automated
Standard Test Methods for Rating and Classifying Inclusions in Steel Using the Scanning Electron Microscope
Methods of Examination of Paint Evidence in Forensic Science Part 3: Scanning Electron Microscopy/X-ray Spectroscopy
Forensic science black powder, pyrotechnic powder element composition inspection scanning electron microscope/X-ray energy spectrometry
TEST METHOD FOR SCANNING ELECTRON MICROSCOPY (SEM) EVALUATION OF WETTED SURFACE CONDITION OF STAINLESS STEEL COMPONENTS
警告：本標準并未指出所有可能的安全問題。在應用本標準之前，使用者有責任采取適當?shù)陌踩徒涌诖胧?，并保證符合國家有關法規規定的條件。 范圍： 本標準規定了環境掃描電子顯微鏡檢測納米顆粒與生物樣品相互作用的技術和規范。 本標準適用于應用掃描電子顯微鏡的低真空和環境真空模式，進行納米顆粒生物效應研究
General guide of environmental scanning electron microscopy for biological effectes on topography induced by nanoparticles
この規格は，乾燥狀態にない試料。揮発性試料,非導電性試料の観察を可能にする特殊な機能及び構造をもたず，試料室の圧力が10 Pa以下で使用可能な走査電子顕微鏡(以下，SEMという。)を用いて，ファインセラミックスのバルク體材料及び粉體才オ料をSEM観察するための試料調製方法について規定する
Sample preparation method of fine ceramics and fine ceramic powders for scanning electron microscope observation
本標準規定了利用掃描電子顯微鏡(SEM)及能譜儀(EDS)觀測環境空氣中細粒子單顆粒形貌、定性分析元素，對環境空氣顆粒物進行分類的方法。掃描電鏡用于顆粒物的形貌觀察和粒徑測量，X射線能譜儀用于顆粒物主要元素定性分析。 本標準適用于在電子束轟擊下穩定的顆粒物分析，不適用于硝酸鹽、銨鹽等熱不穩定的
Microbeam analysis—Scanning electron microscopy with energy dispersive X-ray spectrometry—Morphology and element analysis of single fine particles in ambient air
本標準規定了用掃描電子顯微鏡及X射線能譜儀對沉積巖自生粘土礦物的晶體形態及化學成分進行鑒定的方法。 本標準主要適用于石油地質沉積巖中常見自生粘土礦物鑒定分析。其他自生粘土礦物鑒定分析可參照?qǐng)?zhí)行
Identification method of authigenic clay mineral in sedimentary rock by SEM & XEDS
This test method is useful for the direct measurement of the thicknesses of metallic coatings and of individual layers of composite coatings
Standard Test Method for Measurement of Thickness of Metallic Coatings by Measurement of Cross Section with a Scanning Electron Microscope
本標準也適用于多壁碳納米管
Characterization of Single-Walled Carbon Nanotubes Using Scanning Electron Microscopy and Energy Spectroscopy
Test Method for Determining Concentration of Airborne Single-Crystal Ceramic Whiskers in the Workplace Environment by Scanning Electron Microscopy
BS ISO 14966. Ambient air. Determination of numerical concentration of inorganic fibrous particles. Scanning electron microscopy method
This International Standard specifies a method using scanning electron microscopy for determination of the concentration of inorganic fibrous
Ambient air - Determination of numerical concentration of inorganic fibrous particles - Scanning electron microscopy method
This International Standard specifies a method using scanning electron microscopy for determination of the concentration of inorganic fibrous
Ambient air - Determination of numerical concentration of inorganic fibrous particles - Scanning electron microscopy method
1.1 This test method covers the measurement of metallic coating thicknesses by examination of a cross section with a scanning electron microsope (SEM
Standard Test Method for Measurement of Thickness of Metallic Coatings by Measurement of Cross Section with a Scanning Electron Microscope
