共找到 150 條與 脫模溫度 相關的標準，共 10 頁
本文件規定了混凝土制品用脫模劑(以下簡稱脫模劑)的術語和定義、分類和標記、一般要求、技術要求、試驗方法、檢驗規則以及包裝、出廠、運輸和貯存。 本文件適用于非純油類物質的混凝土制品用脫模劑
Release agents for concrete products
本規范規定了脫醇型單組份室溫硫化硅橡膠的要求。本規范適用于活性基團封端的聚二甲基硅氧烷與填料、交聯劑等助劑制成的脫醇型單組份室溫硫化硅橡膠 GD 406、GD 407、GD 414
Specification for dealcoholized one-component room temperature vulcanized silicone rubber
This International Standard specifies a method for the determination of the temperature at which plastics that are not rigid at normal ambient
Plastics -- Determination of the brittleness temperature by impact
本標準規定了制備熱塑性塑料壓塑試樣和制備可用于機械或沖壓加工成試樣的壓塑片料所必須遵循的總的原則和步驟
Plastics--Compression moulding test specimens of thermoplastic materials
本標準規定了復合材料樹脂傳遞模塑（壓注）成型工藝的設備與工裝、材料、環境、工藝過程、常見缺陷及解決措施、質量控制、安全與衛生等。 本標準適用于航空復合材料制件樹脂傳遞模塑（壓注）成型工藝
Composite resin transfer molding (injection) molding process
This specification covers a mold release agent in the from of a liquid. This produce has been used typically for application to molds used
Mold Release Agent
MOLD RELEASE AGENT
Knock-out bar for die shank
本標準規定了制備熱塑性塑料模壓試樣和試片的一般原理和步驟，試樣可以通過機加工或沖壓的方法從試片上獲得。 為了獲得具有重復性的模塑件，包括四種不同的冷卻方法的主要加工步驟都是標準的。對每一種材料，模壓時需要的模塑溫度和冷卻方法應按照有關材料的國際標準中的規定或由有關利益雙方商定
Plastic.Compression moulding of test specimens of thermoplastic materials
This specification covers a mold release agent in the form of a liquid
MOLD RELEASE AGENT
This specification covers a mold release agent in liquid form
MOLD RELEASE AGENT
MOLD RELEASE AGENT
Mold Release Agent
Mold Release Agent
This specification covers a mold release agent in the form of a liquid
MOLD RELEASE AGENT
