共找到 150 條與 采氣瓶 相關的標準，共 10 頁
本方法適用于惡臭污染源排氣和環境空氣中硫化氫、甲硫醇、甲硫醚和二甲二硫的同時測定。氣相色譜儀的火焰光度檢測器（GC-FPD）對四種成分的檢出限為0.2×10-9～1.0×10g，當氣體樣品中四種成分濃度高于1.0mg/m3時，可取1～2mL氣體樣品直接注入氣相
Air quality. Determination of sulfuretted hydrogen, methyl sulfhydryl, dimethyl sulfide and dimethyl disulfide. Gas chromatography
本規程適用于正常環境溫度（-40度~60度，注1-1）下使用，公稱容積為0.4L~3000L,公稱工作壓力為0.2Mpa~35Mpa(表壓，下同）且壓力與容積的乘積大于或者等于1.0Mpa，盛裝壓縮氣體，高（低）壓液化氣體，低溫液化氣體，溶解氣體，吸附氣體，標準沸點等于或者低于60度的液體以及
Supervision Regulation on Safety Technology for Gas Cylinder
Technical requirements for hydrogen sampling for proton exchange membrane fuel cell vehicles
本標準規定了氣瓶氣密性試驗的試驗裝置和試驗方法的要求”本標準適用于采用浸水法或涂液法時氣瓶的氣密性試驗
Methods for leakage test of gas cylinders
本標準規定了溫室氣體硬質玻璃瓶采樣系統的組成、采樣環境、采樣時間、采樣流程、樣品的包裝、儲存和運輸、采樣瓶的前處理和后處理、信息記錄格式、質量控制方法等。本標準適用于氣象、環境等科研和業務部門采集本底地區的大氣樣品,以進行二氧化碳、甲烷、氧化亞氮、六氟化硫、氫氟碳化物、全氟化碳、氟氯碳化物、氫氟氯
Greenhouse gases sampling by pyrex flask
本文件適用于晉中市氣瓶追溯管理體系的構建與實施
Gas cylinder traceability management specifications
本標準規定了汽車用壓縮天然氣鋼瓶（以下簡稱鋼瓶）的型式和參數、技術要求、試驗方法、檢驗規則、標志、涂敷、包裝、運輸和儲存等。 本標準適用于設計、制造公稱工作壓力為20 MPa(本標準壓力指表壓），公稱水容積為30 L～300 L，工作溫度為-40 ℃～65 ℃ ，設計使用壽命為15年的鋼瓶。 按
Steel cylinders for the on-board storage of compressed natural gas as a fuel for automotive vehicles
This International Standard specifies requirements for safe handling, use and storage of gas cylinders for compressed, liquefied or dissolved gases
Gas cylinders - Safe handling (ISO 11625:2007, IDT)
This International Standard specifies stamp marking of refillable transportable gas cylinders and tubes of volume greater than 0,5 l and less than
Gas cylinders - Stamp marking (ISO 13769:2007, IDT)
Safety technical requirements for hydrogen filling of vehicle gas cylinders
Language: English Written by: Svenska
Gas cylinders - Precautionary labels (ISO 7225:2005, IDT)
This International Standard specifies the inspection requirements at the time of filling, and applies to seamless or welded transportable gas
Gas cylinders - Cylinders for compressed and liquefied gases (excluding acetylene) - Inspection at time of filling (ISO 24431:2006, IDT)
This International Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests
Gas cylinders - Refillable welded aluminium-alloy cylinders - Design, construction and testing (ISO 20703:2006, IDT)
Diese ?NORM ist für die Ausführung von Probenflaschen für Milch, die insbesondere zur automatischen Probennahme von Rohmilch in Milchsammelwagen
Sample bottle ior milk
LPG cylinder safety management Internet of things specification
