BS EN 16094:2012 層壓木質地板.微劃痕測定試驗方法

Laminate floor coverings. Test method for the determination of micro-scratch resistance

NF P62-400*NF EN 655:2012 彈性地板覆蓋物.帶有聚氯乙烯防磨損層的附聚化合物軟木地板磚.規范

Resilient floor coverings - Tiles of agglomerated composition cork with polyvinyl chloride wear layer - Specification.

ANSI A135.6-2012 工程木質壁板

Establishes a nationally recognized voluntary consensus standard for engineered wood siding that can serve as a common basis for understanding among those manufacturing, specifying or using engineered wood siding. The purpose of the update is to revise ANSI A135.6 and change the title of the Standard.

Engineered Wood Siding

ANSI/HPVA EF-2012 實木復合地板標準

Standard for Engineered Wood Flooring

ASTM D7469-12 建筑用木料產品中的端接件的標準試驗方法

1.1 This standard provides test methods for evaluating the structural capacity and integrity of end-joints in structural wood products. 1.2 End-joints are manufactured by adhesive bonding of machined, mated surfaces at the ends of two pieces of lumber to form a joint. Typical end-joint configurations include finger joints and scarf joints. The combination of one or more end-joints and the adjoining sections of the structural wood product within the assembly is considered to be the test specimen. 1.3 Off-line test methods include: (1) Axial Tension, (2) Bending, and (3) Cyclic Delamination. 1.4 In-line test methods include: (1) Tension Proofload and (2) Bending Proofload. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations pr......

Standard Test Methods for End-Joints in Structural Wood Products

KS K ISO 10833:2011 鋪地織物.用改進的威特曼鼓輪試驗器法對切割邊緣損害的抗性的測定

? ??? ???? ???? ???? ??? ??? ?? ?? ????? ???? ???

Textile floor coverings－Determination of resistance to damage at cut edges using the modified Vettermann drum test

JC/T 2080-2011 木鋁復合門窗

本標準規定了木鋁復合門窗的術語和定義、分類、代號和標記、材料要求、技術要求、檢驗方法、檢驗規則以及標志、包裝、運輸和貯存等。 本標準適用于公共建筑和民用建筑用木鋁復合門窗。 本標準不適用于特殊功能的木鋁復合門窗。

Aluminium-wood window and door

JC/T 2081-2011 實木門窗

本標準規定了實木門窗的術語和定義、分類、代號和標記、材料要求、技術要求、檢驗方法、檢驗 規則以及標志、包裝、運輸和貯存等。 本標準適用于公共與民用建筑用普通實木門窗。 本標準不適用于特殊功能的實木門窗。

Solid wood door and window

BS 8201:2011 木地板和人造木板的安裝操作規程

This British Standard gives recommendations for laying the following types of flooring: Board Pre-assembled board Strip Mosaic Overlay Parquet Block End grain flooring Multi-layer Wood-based panels. This British Standard does not cover the protection afforded to a floor by floor coverings or surface finishes. This British Standard does not cover floors for temporary structures or floors intended for limited use. Different considerations might apply to these floors.

Code of practice for installation of flooring of wood and wood-based panels

KS F 9002-2011 輕結構木建筑結構部的施工標準

? ??? ?? ??? ??? ??? 4.?? ??? ??? ???? ?? ?? ??? ?

Standard practice for constructing structural parts of light-frame wood buildings

DIN EN 13228:2011 木地板.包括帶聯鎖系統的地板塊的鑲木地板構件.德文版本EN 13228-2011

This European Standard specifies the characteristics of solid wood overlay flooring including blocks with an interlocking system. It applies to elements. This standard covers elements with and without surface coating.

Wood flooring - Solid wood overlay flooring elements including blocks with an interlocking system; German version EN 13228:2011

DIN EN 13647:2011 木地板,木鑲板和貼面層.幾何特征的測定.德文版本EN 13647-2011

This European Standard specifies methods of measuring the geometrical characteristics of wood and parquet flooring and wood panelling and cladding elements. This European Standard does not specify sampling, which is intended to be found in the product standards or test methods and it does not apply to elements which are installed.

Wood flooring and wood panelling and cladding - Determination of geometrical characteristics; German version EN 13647:2011

BS EN 13228:2011 木地板.包括有聯鎖系統地板塊的實木表層地板構件

This European Standard specifies the characteristics of solid wood overlay flooring including blocks with an interlocking system for internal use as flooring. It applies to elements. This standard covers elements with and without surface coating.

Wood flooring. Solid wood overlay flooring elements including blocks with an interlocking system

BS EN 13647:2011 木地板,木鑲板和貼面層.幾何特征的測定

This European Standard specifies methods of measuring the geometrical characteristics of wood flooring and wood panelling and cladding elements. This European Standard does not specify sampling, which is intended to be found in the product standards or test methods and it does not apply to elements which are installed.

Wood flooring and wood panelling and cladding. Determination of geometrical characteristics

NF B53-646:2011 木質地板.耐刻痕的測定.試驗方法

Wood flooring - Determination of resistance to indentation - Test method.

JG/T 303-2011 木復合門

本標準規定了木復合門的術語和定義、分類、代號及標記、要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存。 本標準適用于民用建筑室內木復合門。

Wood compound door

DIN EN 1534:2011 木質地板.耐刻痕性測定.試驗方法;德文版本EN 1534-2010

Wood flooring - Determination of resistance to indentation - Test method; German version EN 1534:2010

ASTM D2047-11 用杰姆斯測量機測定拋光涂覆地板表面靜摩擦系數的標準試驗方法

Test Method D2047 establishes a compliance criterion relating static coefficient of friction measurements of flooring surfaces with human locomotion safety. The compliance criterion is based on extensive experiential data from residential, commercial, industrial and institutional walkway surfaces since 1942. Polishes and other floor maintenance coatings having a static coefficient of friction of not less than 0.5, as measured by this test method, have been recognized as providing nonhazardous walkways. Note 18212;The value of 0.5 meets the requirements for compliance with Rule 5 on “The use of terms slip retardant, slip resistant, or terms of similar import,” of the Proposed Trade Practice Rules for the Floor Wax and Floor Polish Industry as issued by the Federal Trade Commission on March 17, 1953. The 0.5 static coefficient of friction compliance criterion of this test method is only appropriate for polish-coated surfaces tested in accordance with this machine and test method. The use of this compliance criterion with other test methods, other test instruments, and other surfaces is improper, because they are not a part of the body of experiential data upon which the conformance criterion is based. Note 28212;The conformance criteria of this test method may be valid for other surfaces and surface coatings tested by this test method, but this has not been substantiated by correlation with experiential data.1.1 This laboratory test method covers the use of the James Machine for the measurement of the static coefficient of friction of polish-coated flooring surfaces with respect to human locomotion safety. Further, this test method also establishes a compliance criterion to meet the requirement for a nonhazardous polished walkway surface. The test method is not intended for use on “wet” surfaces or on surfaces wherein the texture, projections, profile or clearance between the sculptured pattern of the surface does not permit adequate contact between the machine foot and the test surface. 1.2 This test method is the only method appropriate for testing polishes for specification compliance with the floor polish static coefficient of friction criterion. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine

ASTM D2899-11 確定圓木樁允許應力的標準操作規程

This practice is intended for use by associations, technical societies and other groups that develop national design standards and use recommendations for round timber piles. In using allowable stresses established under this practice, factors specific to each end use which may affect the performance of the pile system shall be considered. Such factors include the location of the critical section, the bearing capacity of the soil, the ability of the pile to withstand driving forces and conditions of service.1.1 This practice contains procedures for establishing allowable stresses for round timber piles starting with clear wood strength properties.1.2 Stresses established under this practice are applicable to piles conforming to the quality, straightness, spiral grain, knot, check, shake, and split provisions of Specification D 25.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Establishing Allowable Stresses for Round Timber Piles

NF P63-201-1-1:2010 鑲木地板.釘好的木地板.第1-1部分:技術規范合同單.

Parquet - Parquet to be nailed - Part 1-1 : contract bill of technical specifications.